DigiPara Liftdesigner LDX API
Loading...
Searching...
No Matches
Add a custom dimensioned concrete floor

Treename: Shaft0.Entries1.E0.WallSegments.ConcreteFloor.

 ' from Samples/Src/LDXAPIExamples/Example_LDXEntry.vb

    <APIHelpAttribute(APIHelpModes.FireCalcModel Or APIHelpModes.LoadLD3File, {APIHelpModes.InputParaLDXDoc}, "Shaft0.Entries1.E0.WallSegments.ConcreteFloor.", "LDXEntry~Example_CustomConcreteFloor", "Add a custom dimensioned concrete floor")>
    Public Shared Sub AddCustomConcreteFloor(ByRef ldxDocument As DigiPara.LDX.LDXDocument)

        If ldxDocument.GetLDXObject("Shaft0.Entries1.E0.") Is Nothing Then
            MsgBox("Desired entry not found! Please reload the relevant .ld3 file.")
            Exit Sub
        End If

        Dim ldxEntry As DigiPara.LDX.LDXEntry = DirectCast(ldxDocument.GetLDXObject("Shaft0.Entries1.E0.").LDXType, DigiPara.LDX.LDXEntry)

        ' fetch or create wall segment
        Dim prefix As String = "ConcreteFloor."
        Dim ldxWallSegment As DigiPara.LDX.LDXWallSegment = ldxEntry.Comp.WallSegments.GetByObjectPrefix(prefix)
        If ldxWallSegment Is Nothing Then
            ldxWallSegment = ldxEntry.Comp.WallSegments.Add()
            ldxWallSegment.Hole.CustomObjectPrefix = prefix
        End If

        With ldxWallSegment
            ' set material
            ldxWallSegment.ALTERNATIVE_MATERIAL = DigiPara.LDX.ShaftMaterial.smConcrete ' Or DigiPara.LDX.ShaftMaterial.smFlagVulnerableToWeakHole

            ' and activate
            .Object.Active = True
        End With

        ' set dimensions
        With ldxWallSegment.Hole
            .HoleMode = .HoleMode Or DigiPara.LDX.HoleModes.hmAdditionalHole

            ' put on same wall as entry
            .Comp.Wall = ldxEntry.Comp.Wall

            ' pick alignemt. This is the tricky part.
            ' in X and Y direction, it should fill the whole shaft including the walls
            .PrimaryAxisMode = DigiPara.LDX.MixedAxisModes.mamY Or DigiPara.LDX.MixedAxisModes.mamSourceRoom Or DigiPara.LDX.MixedAxisModes.mamOriginOutside
            .TertiaryAxisMode = DigiPara.LDX.MixedAxisModes.mamX Or DigiPara.LDX.MixedAxisModes.mamSourceRoom Or DigiPara.LDX.MixedAxisModes.mamOriginOutside

            ' In Z-direction, the segment should be aligned to the entry
            .SecondaryAxisMode = DigiPara.LDX.MixedAxisModes.mamZ Or DigiPara.LDX.MixedAxisModes.mamSourceRoom Or DigiPara.LDX.MixedAxisModes.mamOriginParent Or DigiPara.LDX.MixedAxisModes.mamAlignmentLower

            .DZ = 400
            .Z0 = - .DZ

            ' with these all 0, the custom concrete segment would just fill the whole shaft width, we already have standard
            ' geometry that does that.
            .X0 = 0
            .X1 = 0
            .Y0 = -500
            .Y1 = .Object.Shaft.Room.W_4

            ' lastly, we have to awkwardly tell the system to automatically calculate the values we did not set
            With .Object.GetDim("X0")
                .DimMode = .DimMode And Not DigiPara.LDX.SheetFrameOverwriteDimModes.sfodmCalcAuto
            End With
            With .Object.GetDim("DX")
                .DimMode = .DimMode Or DigiPara.LDX.SheetFrameOverwriteDimModes.sfodmCalcAuto
            End With
            With .Object.GetDim("X1")
                .DimMode = .DimMode And Not DigiPara.LDX.SheetFrameOverwriteDimModes.sfodmCalcAuto
            End With

            With .Object.GetDim("Y0")
                .DimMode = .DimMode And Not DigiPara.LDX.SheetFrameOverwriteDimModes.sfodmCalcAuto
            End With
            With .Object.GetDim("DY")
                .DimMode = .DimMode Or DigiPara.LDX.SheetFrameOverwriteDimModes.sfodmCalcAuto
            End With
            With .Object.GetDim("Y1")
                .DimMode = .DimMode And Not DigiPara.LDX.SheetFrameOverwriteDimModes.sfodmCalcAuto
            End With

            With .Object.GetDim("Z0")
                .DimMode = .DimMode And Not DigiPara.LDX.SheetFrameOverwriteDimModes.sfodmCalcAuto
            End With
            With .Object.GetDim("DZ")
                .DimMode = .DimMode And Not DigiPara.LDX.SheetFrameOverwriteDimModes.sfodmCalcAuto
            End With
            With .Object.GetDim("Z1")
                .DimMode = .DimMode Or DigiPara.LDX.SheetFrameOverwriteDimModes.sfodmCalcAuto
            End With
        End With
    End Sub