|
DigiPara Liftdesigner LDX API
|
API method: ILDXShafts.SHAFTS_MODE
2 code examples follow.
' from Samples/Src/LDXAPIExamples/Example_GroupsConfiguration.vb
<APIHelpAttribute(APIHelpModes.FireCalcModel Or APIHelpModes.LoadLD3File, {APIHelpModes.InputParaLDXDoc}, "", "LDXShafts~SHAFTS_MODE", "Left align bank 2 shafts and change their DX and DY offset")>
Public Shared Sub LeftAlignBank2ShaftsAndChangeTheirDXAndDYOffset(ByRef ldxDocument As DigiPara.LDX.LDXDocument)
If ldxDocument.Shafts Is Nothing Then
MsgBox("No shafts found")
Return
End If
' Align left
ldxDocument.Shafts.SHAFTS_MODE = DigiPara.LDX.ShaftsModes.slmNone
ldxDocument.Shafts.SHAFTS_MODE = ldxDocument.Shafts.SHAFTS_MODE Or DigiPara.LDX.ShaftsModes.slmBankAlignmentLeft
' Sideways offset
ldxDocument.Shafts.BANK_DX = 400
' Distance between the two banks
ldxDocument.Shafts.BANK_DY = 5500
End Sub
' from Samples/Src/LDXAPIExamples/Example_LDXMachineRoom.vb
<APIHelpAttribute(APIHelpModes.FireCalcModel Or APIHelpModes.LoadLD3File, {APIHelpModes.InputParaLDXDoc}, "Shaft0.MachineryRoom.", "LDXShafts~SHAFTS_MODE", "Shared machine room")>
Public Shared Sub MergeMachineRooms(ByRef ldxDocument As DigiPara.LDX.LDXDocument)
If ldxDocument.GetLDXObject("Shaft0.MachineryRoom.") Is Nothing Then
MsgBox("Machine room not found! Please reload the relevant .ld3 file!")
Exit Sub
End If
If ldxDocument.Shafts.Count < 2 Then
ldxDocument.Shaft.Object.CloneMe()
ldxDocument.CalculateModel(DigiPara.LDX.CalculateModelModes.rcmCalc)
End If
' make at least one machine room view
Dim sheet = ldxDocument.Sheets.ActiveSheet
Dim found As Boolean = False
Dim toTransform As DigiPara.LDX.LDXSheetFrame = Nothing
For Each frame As DigiPara.LDX.LDXSheetFrame In sheet
If frame.ViewType = DigiPara.LDX.SheetFrameViewType.shfvtMachineryRoom Then
found = True
frame.Activate()
Exit For
ElseIf frame.ViewType = DigiPara.LDX.SheetFrameViewType.shfvtPlan Then
toTransform = frame
End If
Next
If Not found Then
If toTransform Is Nothing Then
toTransform = sheet.Add(DigiPara.LDX.SheetAddOptions.saoCalculateDefaultPlacement)
End If
toTransform.Reset(DigiPara.LDX.SheetFrameViewType.shfvtMachineryRoom, DigiPara.LDX.SheetFrameViewDirections.shfvdToFromTop, DigiPara.LDX.SheetFrameResetOptions.shfrrstInitText)
toTransform.Activate()
End If
With ldxDocument.Shafts
If (.SHAFTS_MODE And DigiPara.LDX.ShaftsModes.slmSharedMachineRoom) <> DigiPara.LDX.ShaftsModes.slmSharedMachineRoom Then
' merge machine rooms
.SHAFTS_MODE = .SHAFTS_MODE Or DigiPara.LDX.ShaftsModes.slmSharedMachineRoom
' The UI code also activates the sharing flag on all shafts individually, but that is not really required
' For Each shaft As DigiPara.LDX.LDXShaft In ldxDocument.Shafts
' shaft.MachineRoom.Merge(shaft.Comp.SX > 0)
' Next
Else
' deactivate shared machine rooms
.SHAFTS_MODE = .SHAFTS_MODE And Not DigiPara.LDX.ShaftsModes.slmSharedMachineRoom
' recalculate machine rooms to make them small again (Just for demo purpsoes, result is likely wrong)
For Each shaft As DigiPara.LDX.LDXShaft In ldxDocument.Shafts
' also from the UI code
' shaft.MachineRoom.Merge(False)
shaft.MachineRoom.Room.DEPTH = shaft.Room.DEPTH
shaft.MachineRoom.Room.Width = shaft.Room.Width
shaft.MachineRoom.Room.X0 = 0
shaft.MachineRoom.Room.Y0 = 0
Next
End If
End With
End Sub